The writer is making a few good annotation relating to Tools You Need to Install a New Bathtub as a whole in this article down the page.
Setting up a tub isn't precisely rocket science, but it does need strong plumbing, woodworking, as well as often, tiling skills. Replacing an old bath tub with a new one is also a reasonably challenging task. If the old tub is conveniently obtainable, the job can relocate rapidly; if you need to open a wall surface to remove the old bathtub and place the brand-new bathtub, the job is a lot harder. In either case, the job is within a residence handyman's skills, although you will require an assistant to vacate the old tub as well as set in the new one. Ensure you have qualified on your own for the task as well as are comfortable trying it. As opposed to working with a specialist to take over a halfway-completed job, it is better to consider using one prior to you begin. Opportunities are you may require an expert plumber to make tube connections.
This write-up will certainly aid you install a brand-new bath tub in your shower room if you have already bought a new tub and also don't need to transform the plan of your previous supply of water pipelines.
Your tools as well as product checklist need to consist of the following:
Planning for the Installment
To start with, the supporting structure provided with the bathroom should be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is very important to see to it that if the faucet comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to avoid stress on the tub.
Fit the versatile faucet adapters to the bottom of both faucets making use of 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet with the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you use every one of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its final placement.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is disconnect the water supply. After doing so, activate the faucets to drain any kind of water continuing to be in the system. The process of getting rid of the existing taps can be quite problematic as a result of the restricted access that is often the instance.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the taps. Have a towel ready for the continuing to be water that will come from the pipelines. Once the supply pipes have actually been gotten rid of, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from transforming throughout this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will have to be cleaned of any old sealing compound.
Prior to moving on to fit the new faucets, contrast the pipeline links on the old taps to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.
Setting up the Bathtub
Making use of both wooden boards under its feet, place the bath tub in the required setting. The wooden boards are valuable in uniformly spreading out the weight of the bathtub over the location of the boards rather than concentrating all the weight onto 4 tiny factors.
The next goal is to make certain that the tub is leveled all round. This can be accomplished by inspecting the level and also readjusting the feet on the tub up until the spirit level checks out level.
To mount faucets, fit all-time low of the outermost versatile faucet port to the proper supply pipe by making a compression sign up with; after that do the very same for the various other faucet.
Turn on the water as well as inspect all joints and brand-new pipework for leakages and tighten them if essential. Fill the tub as well as additionally check the overflow outlet as well as the typical electrical outlet for leakages.
Ultimately, fix the bath paneling as described in the producer's instruction manual. Tiling as well as sealing around the tub ought to wait up until the tub has been utilized a minimum of once as this will resolve it right into its last setting.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end supplies a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the faucet in the mounting opening in the bath/basin ensuring that the washers remain in area in between the faucet as well as the sink. Safeguard the faucet in place with the maker supplied backnut. When the tap is firmly in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular tap connectors. The previous type must be attached to the tap finishes initially, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the area where the bath fulfills the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to split a rigid seal, creating the water to pass through the wall in between the bath and also the tiling, causing problems with wetness as well as feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your components as well as installations. They are sold in tubes as well as cartridges, and also can sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill up the bath tub with water prior to securing, to allow for the movement experienced when the tub is in use. The sealant can crack fairly early if you do not take into consideration this motion before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise easily readily available on the marketplace. It is suggested to fit the tiles utilizing waterproof or waterproof glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you enjoyed reading our part about How to Install a Bathtub. Thank you for spending some time to browse our blog post. Sharing is nice. Helping others is fun. Thanks a lot for taking the time to read it.
Need fast action?